Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
Just how do you actually feel about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a new one is also a moderately tough job. If the old bathtub is conveniently accessible, the job can relocate easily; if you need to open a wall to remove the old tub and position the new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the task and fit trying it. Instead of working with a specialist to take over a halfway-completed task, it is better to consider employing one before you start. Possibilities are you may require an expert plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your restroom if you have actually currently acquired a brand-new bathtub as well as don't need to transform the setup of your previous water pipes.
Your devices and material checklist ought to comprise the following:
Preparing for the Setup
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water staying in the system. The procedure of removing the existing faucets can be rather bothersome due to the limited gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to moving on to fit the new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing both wood boards under its feet, put the bath tub in the needed placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bathtub up until the spirit level checks out level.
To set up taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Activate the water and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill the bathtub as well as also examine the overflow outlet and the normal outlet for leaks.
Ultimately, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and also securing around the tub should wait until the bath tub has actually been used at least when as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in area between the tap and the sink. Protect the tap in place with the producer given backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous type ought to be connected to the faucet ends first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing complications with moisture and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking time to read our piece. Liked our content? Please share it. Let someone else locate it. Kudos for your time. Visit us again soon.
Top-notch service? Dial here. Report this page